- Modelsim pe does not install how to#
- Modelsim pe does not install update#
- Modelsim pe does not install download#
- Modelsim pe does not install windows#
Note If additional issues occur, or if any troubleshooting is required, you might have to create a separate service request. If this section does not appear, contact Microsoft Customer Service and Support to obtain the hotfix.
Modelsim pe does not install download#
If the hotfix is available for download, there is a "Hotfix download available" section at the top of this Knowledge Base article.
Modelsim pe does not install update#
Therefore, if you are not severely affected by this problem, we recommend that you wait for the next software update that contains this hotfix. This hotfix might receive additional testing. Apply this hotfix only to systems that are experiencing the problem described in this article. However, this hotfix is intended to correct only the problem that is described in this article.
Modelsim pe does not install windows#
Hotfix information for the Windows ADK for Windows 10, version 1511Ī supported hotfix is available from Microsoft Support. Specify where the boot image is distributed (System Center 2012 Configuration Manager)ĭistribute boot images to a distribution point (current branch) Update the boot images by using the methods that are described in the following TechNet articles: Manage boot images with System Center Configuration Manager (current branch)
Modelsim pe does not install how to#
How to manage boot images in Configuration Manager (System Center 2012 Configuration Manager) Note This step is not required for an existing boot image.Īdd the boot images by using the methods that are described in the following TechNet articles: To do this, type the following command, and then press Enter:ĭism /unmount-wim /mountdir:C:\WinPE_amd64\mount /Commitįor information about dism commands, see DISM Image Management command-line options. Icacls c:\WinPE_amd64\mount\Windows\System32\ /restore "%temp%\AclFile"Ĭommit the changes to the boot.wim file. Icacls c:\WinPE_amd64\mount\Windows\System32\schema.dat /setowner "NT SERVICE\TrustedInstaller" When the schema.dat file is replaced, the permissions saved in step 5 must be restored by running the following commands: Xcopy "%userprofile%\Downloads\schema-圆4.dat" c:\WinPE_amd64\mount\Windows\System32\schema.dat /Y Icacls c:\WinPE_amd64\mount\Windows\System32\schema.dat /grant BUILTIN\Administrators:(F)
Takeown /F c:\WinPE_amd64\mount\Windows\System32\schema.dat /A To do this, type the following commands, and then press Enter after each command: To replace the schema.dat file that has the updated version, you must take ownership of the file and grant permissions to the local administrators group. Icacls c:\WinPE_amd64\mount\Windows\System32\schema.dat /save "%temp%\AclFile" To back up the file, type the following command, and then press Enter: Note The copype.cmd amd64 c:\WinPE_amd64 command is not required for an existing boot image.įor information about dism commands, see DISM Image Management command-line options.īack up the permissions that are applied to the existing schema.dat file before you replace it. To do this, type the following commands, and then press Enter after each command:ĭism /mount-wim /wimfile:C:\WinPE_amd64\media\sources\boot.wim /index:1 /mountdir:C:\WinPE_amd64\mount Start an elevated “Deployment and Imaging Tools Environment” command prompt.Ĭreate the Windows PE customization working directory, and then mount the image file. For example, extract the contents to the %userprofile%\downloads folder. To update existing boot images, follow these steps but change the paths in the command lines to point to the existing boot images.Įxtract the contents of the hotfix. Instead of creating new boot images, existing boot images based on the same ADK can also be updated using these steps. The following steps 1-9 are written for new boot images following the installation of the Windows ADK. The steps, as written, assume a 64-bit (amd64) architecture. Be aware that amd64 or x86 should be used in the commands here, depending on the processor architecture that's required. These steps assume that the Windows ADK for Windows 10, version 1511, is already installed, and that the user who performs the steps is a member of the local Administrator group. The following steps are required to update the Windows Image file (boot.wim) with this hotfix, and to update the image on Configuration Manager distribution points. This issue is also described in the Issue with the Windows ADK for Windows 10, version 1511 blog post. Note This log entry is truncated for readability. PAnswerFile->AddNetworkAdapter(adapterInfo), HRESULT=80220014ĪdapterSettings.Configure( pAnswerFile ), HRESULT=80220014
M_pImpl->AddAdapterTcpIpSettings( XMLAnswerFileImpl::WindowsPE, adapterInfo ), HRESULT=80220014